C&K systems System 236i Instruções de Operação Página 1

®Using yourAlpha Plus keypadWith yourPart Number 5-051-373-00 Rev BSystem 236System 238System 2316qqqqqqSystem 236iSystem 238iSystem 2316i

10AUTO HOME ARMINGMake sure the display reads READY TO ARM.Enter your PIN and push the# key.PINREQUIRED.If you do not exit before the exit delay time

11The keypad will beep twice to confirm that the system is armed,and the display will read ARMED - INSTANT.INSTANT ARMINGInstant Arming converts all t

12HOME ARMINGHome Arming arms perimeter zones, while bypassing interior zones.Make sure that the display reads READY TO ARM.Enter your PIN (if require

13INSTANT HOME ARMINGEnter your PIN (if required),push the key, enter the digit "7",the digit "4", then push the # key.PINREQU

14Push the key, enter the zone to bebypassed, then push the # key.BYPASSING ZONESThis procedure allows you to bypass one or more zones while y

15ZONE #ZONE #.To bypass more than one zone: enter yourPIN (if required), push the key, enter thefirst zone to be bypassed, push thekey again,

16This procedure allows you to bypass one or more zones while your system isDISARMEDBYPASSING ZONESNOTE: System programming determines which PINs can

17.To indicate that zones are bypassed, the display will read BYPASSED ZONE. To seewhich zones are bypassed, push the # key.The procedures for adding

18Your alarm system has been programmed for one of the following arming types:FORCE ARMINGAny zone (except for 24-hour zones) that is violated during

19CHIRP ALERT (Available on Systems 238, 238i, 2316 and 2316i ONLY)The system will arm even if delayed or interior zones are faulted at the time ofar

2Thank you for purchasing this C&K alarm system. Your system is one of the most powerfuland advanced alarm systems on the market today designed t

20TO DISARM THE SYSTEM:Enter only through a TIME DELAY door..OPTIONINSTALLEDThe display will read ENTRY - DISARM NOW. A bar graph will appear on the

21AFTER AN ALARM OCCURS:Enter your PIN and push the# key.This will silence the bell/siren and disarm the system..The display will read ALARM ZONE. To

2224-HOUR MONITORINGWith this option installed, your alarm system will transmit alarm signals toour central station.EMERGENCY KEY (Available on System

23POLICE/PANIC KEYWhen this option is installed, holding down the POLICE keyfor three seconds will trigger an alarm. The keypad will beeptwice to con

24Should an intruder force you to turn your security system off or on, you cansend a silent DURESS signal to our central station by entering User Code

25GUEST COMBINATION (Not Available on System 236/236i)The SYSTEM 238 and 238i can store up to 8 PINs and the SYSTEM 2316 and 2316i up to32 PINs. In

26User 1 can use his Master PIN to change the PINs of Users 1 - 8.CHANGING A USER PIN - SYSTEM 238 and 238iEnter your Master PIN, pushthe key, ent

27Exit the programming mode by pushing the key, then the # key.Make sure the new PIN works.#**After leaving the programming mode, Arm and Disarm you

28DELETING A USER PIN - SYSTEM 238 and 238iOPTIONINSTALLEDEnter your Master PIN, pushthe key, enter the digit "0", thenpush the # key.0M

29User 1 can use his Master PIN to change the PINs of Users 1 - 6 (on System236 and 236i) or Users 1 - 32 (on System 2316 and 2316i).CHANGING A USER P

3Table of contentsGetting acquainted ... 4-5What the lights mean...

30System: 236, 236i, 2316,and 2316i ONLYEnter the new PIN again and pushthe # key.#If the new PIN is accepted, the keypad will beep twice, and the di

31User 1 can use his Master PIN to delete the PINs of Users 2 - 6 (on System236 and 236i) or Users 2 - 32 (on System 2316 and 2316i) (See note pg. 29)

32Enter zero and push the # key.0Enter zero (again) and push the # key.0Exit the programming mode by pushing the key, then the # key.##*#*System:

33RESETTING SMOKE DETECTORSWhen a smoke detector is triggered, the keypad display will read ALARMZONE, and the bell/siren will sound.OPTIONINSTALLEDBe

34DOOR CHIMEWhen this option is installed, all keypads on the premises will beep for twoseconds each time a designated zone is faulted.OPTIONINSTALLED

35LOCAL SYSTEM TESTThis option allows on-site testing of each zone in your system.To initiate the SYSTEM TEST:Enter your PIN (if required),push the

36STANDBY BATTERY TESTYour alarm system can be programmed to automatically test its standbybattery every 24 hours. During the test, AC power is turne

37The display will read TEST REPORTING.CENTRAL STATION TESTThis option tests the reporting capability of your system by sending a testmessage to the c

38IF YOU HAVE TELEPHONE TROUBLE:First, unplug the control panel from its telephone jack to determine if thealarm system is causing the trouble.The pho

39To turn the backlight on or off, push the keyenter the digit "8", then push the # key.To turn the door chime tones on or off (at each

4What your alarm system is...Your alarm system is made up of a control panel and several detection devices like motion sensors,magnetic contacts, and

403 1#*3 2#*3 3#*Key CombinationsThe ALPHA Plus keypad is programmed to display messages in several different languages. Use the combinationshown in

41CBED-ROOMBEDROOMBASEMENTPlace detectors neartop of stairwellsBEDROOM BEDROOM KITCHEN DININGROOMBEDROOM LIVING ROOM= SMOKE DETECTORKBED-ROOMBED-ROOM=

42Every household should establish and regularly practice an escape plan in the event of a fire. The followingsteps, recommended by the National Fire

43ALARMA condition that occurs when the detection devices in a zone aretriggered after the system is armed.ALARM MEMORYAlarm conditions are stored in

44THE LIMITATIONS OF YOUR ALARM SYSTEMWhile your alarm system is reliable and sophisticated, it does not offer guaranteed protection against burglary

45As required by UL Standard 1023, your alarm system is a Grade "A" system(see definition on page 43).Alarm system malfunctions and failures

46LOCATIONYES NOBYPASSZONE123456

47LOCATIONYES NOBYPASS12345678ZONE

48LOCATIONYES NOBYPASS910111213141516ZONE

49Notes

5Each alarm system in the 2300 family is designed to meet the specific needs of a variety of applications. System 236is specifically designed for sma

50FCC NOTICEWARNING: This device is intended to be installed by a professional alarm installer. The user shall be cautioned that changes or modifica

51Industry CanadaNOTICE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment

52®C&K is a registered trademark of C&KComponents, Inc.Copyright 1995 C&K SYSTEMS, Inc.All Rights ReservedC&K SYSTEMS, Inc.107 Woodmer

6ARMEDLIGHTPOWERLIGHTREMARKSAC POWER FAILURELOW BATTERYSYSTEM ARMEDSYSTEM DISARMEDSYSTEM IS ARMEDWITH DELAY ZONESCONVERTED TO INSTANTSlow FlashOnOffP

7*Not available on System 236/236iSOUND MEANING2 beeps system armed or disarmed.successful central station test or battery test.5 beepsunauthorized co

8Make sure the display reads READY TO ARM.Faulted zones must be cleared or bypassed before the system can be armed. If thedisplay reads NOT READY TO

9Make sure the red ARM light comes on.The keypad will beep twice to confirm that the system is armed..The display will read EXIT NOW..Exit through any